Condenser and Evaporator in Refrigeration System：
What is the Difference

Most outages of chillers trace back to two parts. One part takes heat away from your process. The other part dumps that heat to the air or to water. Those two parts are the evaporator and the condenser. They look like metal and tubes, but they run the entire show.

This article explains what each one does, how they differ, how they work together, and how to keep them happy in day to day service.

What is the Evaporator in a Chiller

In refrigeration industrial, people usually think of the evaporator as the cooling side. Its job is to pull heat out of your process fluid. That fluid could be water, a glycol mix, or something special for your process.

Refrigerant enters the evaporator as a low pressure liquid. In the heat exchange surface it absorbs process heat and boils into vapor. That phase change is the source of cooling power.

Types you will see in the field include plate heat exchangers and shell and tube units. Plate units give compact area in a small footprint. Shell and tube holds up well in large systems and in tough cleaning cycles. The plate type moves heat fast. The shell type handles heavy flows and dirty fluids better.

What is the Condenser in a Chiller

The condenser is the heat rejection side. It takes the hot refrigerant vapor from the compressor and turns it back into liquid. That means the condenser carries the heat the evaporator picked up plus the work done by the compressor.

You will see air cooled condensers and water cooled condensers on plants. Air cooled condensers use fans to push air across finned coils. They are simple and need no cooling tower. Water cooled condensers use cooling tower water and are usually more efficient for large loads. Both have to move heat fast. If the condenser can not reject heat the entire system pays in higher pressure and higher energy use.

What is the Difference Between the Evaporator and Condenser

They both move heat but they do opposite jobs. The evaporator removes heat from the process fluid and makes it cold. The condenser rejects that heat to the outside and makes the refrigerant liquid again. Think cold side and hot side.

Another difference is where they sit in the cycle. Refrigerant leaves the expansion device into the evaporator. After the evaporator the refrigerant goes to the compressor. From the compressor it moves to the condenser and then back through the expansion device.

They also have different failure modes. The evaporator suffers from scaling and freezing. The condenser suffers from fouling and airflow problems.

How the Evaporator and Condenser Work Together

They run in a loop and they rely on each other. The evaporator takes heat from your process. The compressor raises refrigerant pressure and temperature. The condenser rejects that added heat to the ambient. The refrigerant then becomes liquid and repeats the loop. If either side falls behind the loop backs up. You see high energy use, pressure shifts, and poor temperature control.

Condenser and Evaporator in Refrigeration System What is the Difference - chiller evaporator（images 2）

Explore high-efficiency and energy-saving chiller solutions！

Get Product Catalogs

Evaporator and Condenser Maintenance Tips for Daily Use

Good maintenance keeps the compressor out of the shop.

Evaporator care

Hard water and suspended solids make scale and fouling. That reduces heat transfer quickly. Keep a regular cleaning cadence if your process water is dirty. Check the strainer and clean it when pressure drop grows. Monitor the chill water leaving temperature and the temperature approach across the exchanger.

Watch for frost on the evaporator. Frost can mean low refrigerant charge or bad airflow in indirect systems. Check the expansion valve and make sure the TXV or electronic valve is responding. If the evaporator is plate type keep the gasket condition in mind. A leaking gasket moves fluids where they should not go.

Condenser care

For air cooled condensers keep fins clean and straight. A few minutes with a soft brush or a low pressure wash can recover a lot of lost performance. Make sure fan belts and motors are tight and balanced. Vibration kills bearings and shortens fan life.

For water cooled condensers focus on water treatment. Scale forms fast when the water carries minerals. Use proper chemistry and blowdown practice. Keep your tube cleaning schedule and watch approach temperature at the condensate side. If approach widens the tubes probably need cleaning.

Common checks for both sides

Look at operating pressures at steady state. A sudden rise in suction or discharge pressure tells you something changed. Log temperatures and pressures for a week and look for trends. Trend data finds slow declines far better than one off checks.

Train operators to report small changes. A tiny rise in leaving water temperature might mean a strainer needs cleaning. Quick fixes save days of downtime.

Conclusion

Both the condenser and evaporator function as heat exchangers, but their positions and functions within the refrigeration cycle differ. We hope this article has helped you understand the differences between them and the key maintenance points.

Click here to contact us for more information about our chillers, or to request our product catalog and detailed price list.

Let us know your requirements