Wuxi Guanya Refrigeration Technology co., ltd

Expansion valve description of cooling water circulation machine for electric vehicle parts testing

The demand for electric vehicle parts testing cooling water circulation machine in the testing of new energy vehicle battery industry is rising, so the choice is very important. Among them, the expansion valve is a more important accessory, and we also need to understand its performance.

The electronic expansion valve of the cooling water circulation machine for electric vehicle parts testing mainly consists of four parts. The rotor is equivalent to the rotor of a synchronous motor, and the valve stem is connected to control the opening of the valve hole. The stator is equivalent to the stator of synchronous electronics; it converts electrical energy into a magnetic field. Drive the rotor to rotate, the valve needle is driven by the rotor, the end is tapered, and moves up and down to adjust the flow rate. The valve body is generally made of brass.

Electronic expansion valve suction superheat control, suction superheat control system is composed of electronic expansion valve, pressure sensor, temperature sensor and controller. When working, the pressure sensor will evaporator outlet pressure P1 and the temperature sensor will suck the compressor through The heat is transmitted to the controller, and the controller processes the signal, and then outputs a command to act on the stepper motor of the electronic expansion main valve to open the valve to the required position.

It takes only a few seconds for the electronic expansion valve to change from fully closed to fully open. The reaction and action speed is fast. The opening and closing characteristics and speed can be set manually; the electronic expansion valve can be adjusted within a specific range and the adjustment range It can be set according to the characteristics of different products.

When testing and installing electronic expansion valves for electric vehicle parts, the centerline of the valve body and coil section should be taken as the axis, and the coil should be upward. When welding the electronic expansion valve and the filter screen, the valve body needs to be cooled and protected, so that the temperature of the valve body does not exceed 120°C, and to prevent impurities from entering the valve body. In addition, the flame should not be directed at the valve body, and at the same time, nitrogen should be filled into the valve body to prevent the generation of oxides. The output voltage of the controller must be consistent with the specified voltage of the coil. If the applied voltage does not match the specified voltage, the coil will burn out or the valve needle will act abnormally.

Before installing the expansion valve, please refer to the installation guide provided by the manufacturer to avoid unnecessary failures.
Related News
Related Products
  • SLJ -110℃~-150℃

    SLJ -110℃~-150℃

    January 11, 2018Temperature ranges from - 5 ~ - 150 ℃, can meet different temperature; Adopt environmental protection refrigerants; Famous brand semi-closed piston compressor, semi-closed bipolar piston compressor, semi-hermetic screw compressor, main brand are BOCK.view
  • Single Fluid Heat Transfer System SR

    Single Fluid Heat Transfer System SR

    April 10, 2018Working temperature range from -25℃to 200℃, other temperature range need to set to the widest temperature range(-50℃to 250℃) Centralized control of 2~20 reactors, each reactor's and jacket temperature can be set independently. One system control multipleview
  • Reactor Temperature System ZLF

    Reactor Temperature System ZLF

    April 10, 2018A set of cooling heat exchanger, heat exchanger, through proportional adjusting valve control cold heat into the heat exchanger, then through the uniform medium input to the reactor jacketed to do heat exchange and temp. Control, system has inside expansiview
  • LT -45℃~30℃

    LT -45℃~30℃

    April 10, 2018Low Temperature Cooling Chiller LT model: LT-5018N,LT-5040N,LT-5062N,LT-5090N,LT-50A1N,LT-50A2N; Medium Temperature Range: -45℃~30℃. ASET multifunctional controller, control outlet temperature of water tankview
  • IC Test Temperature System      -45℃~250℃

    IC Test Temperature System -45℃~250℃

    February 28, 2019-45℃~+200℃ 2.5kW~25kW ±0.3℃view
  • Flash EMMC Temperature Test  -85℃~200℃

    Flash EMMC Temperature Test -85℃~200℃

    February 28, 2019Temperature control range:-85 ° C ~ 200 ° CPower range:2.5kW~25kWTemperature control accuracy:±0.3°CModelTES-8525WTES-8555WTES-85A10WTES-85A15WTES-85A25WTemp. Range-85℃~200℃-85℃~200℃-85℃~200℃-85℃~200℃-85℃~200℃Heating P...view
products
Contact
Tel: + 86 18751545184
E-mail: sales@cnzlj.com
Add: No.203, Hongyun Road, Hongshan Street, Optoelectronics Park, Xinwu District, Wuxi City, Jiangsu Province, China
code chat